Termi Slab Seal is a one-way, non-return valve designed for injecting termiticide through concrete slabs, paths and other hard surfaces during termite treatments. Fitted into a standard 14 mm drill hole, it seals the injection point so chemical goes into the substrate rather than back onto the technician or the customer’s floor.

What it is
Drilling and injecting through concrete is a routine part of chemical termite management in Australia. Where a slab-on-ground home, patio, garage or driveway abuts the building, the soil beneath must be treated to complete a continuous chemical barrier, and the only way in is through the concrete. The weak point of the job has always been the drill hole: without a seal, injected liquid can blow back out of the hole, pool on the surface, stain finishes and expose the technician and occupants to chemical.
Termi Slab Seal addresses this with a plug containing a one-way, non-return valve with four sealing points. The seal is designed to deliver maximum penetration of termiticide across concrete areas and across soil and clay substrate types, according to the manufacturer.

Key benefits
- Less chemical wastage. The non-return valve stops termiticide escaping back through the hole, so more product reaches the soil.
- Faster jobs. No need to stop and clean up blow-back, and injection points can be revisited.
- Protects the technician, the home-owner and the environment. Reduced surface contamination means less chemical exposure and less run-off.
- Simple to fit. One drill size, one plug, one injection rod.
- Lower cost per job. Savings in chemical and time add up over a treatment program; ask your branch for details.
How to use Termi Slab Seal
- Drill a 14 mm hole through the concrete at the spacing required by the termiticide label and Australian Standard AS 3660.2 for the treatment you are carrying out.
- Fit the Termi Slab Seal into the hole. It must sit level with the top of the slab.
- Attach the Termi Slab Seal injection rod to your injection equipment and inject termiticide through the one-way valve into the substrate.
- Move to the next hole. The valve closes behind the rod, holding chemical in the soil.
A full instruction guide and demonstration DVD are available from your Garrards branch.

Where it fits in a termite management program
Termi Slab Seal is a delivery accessory, not a termiticide. It is used wherever other concrete injection seals or plugs would be used: perimeter treatments around slab-on-ground homes, treatments beneath concrete paths, patios and garage floors, and remedial treatments where a chemical soil barrier must be completed under hard surfaces. Use it with the termiticide of your choice, applied at label rates.

Safety and compliance
- Termiticides must be APVMA-registered and applied in accordance with the product label and AS 3660.2.
- Chemical termite treatments must be carried out by a licensed pest management technician under the relevant state or territory legislation.
- Wear the PPE specified on the termiticide label when drilling and injecting, and follow safe work practices for concrete drilling (dust control, eye and hearing protection, service location before drilling).
- Record injection points and product volumes on the treatment certificate as required by AS 3660.2.
Video
Watch the full Termi Slab Seal presentation: Termi Slab Seal video on YouTube.
Frequently asked questions
What size hole does Termi Slab Seal need?
A 14 mm hole drilled through the slab. The seal must be fitted level with the top of the concrete.
Does it work in clay soils?
The manufacturer states the seal is designed for all soil and clay substrate types. Injection volumes and spacing should still follow the termiticide label for the soil conditions on site.
Do I need a special injection rod?
Yes. Termi Slab Seal rods are used to open the one-way valve and inject chemical through it.
Available from Garrards
Termi Slab Seal plugs and injection rods are available from Garrards branches across Australia. Ask in store for the instruction guide, demonstration DVD and current pricing.
Contact your local Garrards branch
Frequently asked questions
What size hole does Termi Slab Seal need?
A 14 mm hole drilled through the slab. The seal must be fitted level with the top of the concrete.
Does it work in clay soils?
The manufacturer states the seal is designed for all soil and clay substrate types. Injection volumes and spacing should follow the termiticide label.
Do I need a special injection rod?
Yes. Termi Slab Seal rods are used to open the one-way valve and inject chemical through it.
