Kordon

KORDON KOLLAR 60MM 100 IN A BOX

Active ingredientDeltamethrin 4 g/kg (equivalent to 2 g/m² deltamethrin).

Code KORD/50

Downloads

Product details

Formulation

This is a pre-formed collar made from treated sheet material. Australian Standard AS 3660.3 classes this type of material as a 'Treated Sheet'. The sheet is non-woven polyester fibre webbing impregnated with deltamethrin, a synthetic pyrethroid, and laminated between two UV-stabilised polyethylene films. The top film is orange.

Overview

Kordon Kollar is a pre-formed termite collar that fits over pipes passing up through a concrete slab. Termites can get into a building unseen through the gaps around these pipes. The collar is installed during construction, before the slab is poured.

The collar works in two ways. It is a physical barrier, and the deltamethrin inside it repels termites. Termites tend to avoid the collar and look for food elsewhere. If they try to go around it, they have to build mud tubes in the open, where a qualified Timber Pest Inspector can find them at a routine inspection. This means the colony can be dealt with before it does serious damage.

Kordon Kollar is a registered component of the Kordon Termite System (APVMA approval no. 60759/100619). Kordon was developed and is made in Australia. The system meets AS 3660.1:2014 and holds a CodeMark Certificate of Conformity.

Product Highlights

  • Pre-formed and ready to fit: it slides straight over the pipe, so there is no need to cut and tape a collar-and-patch detail from Kordon sheet on site. This saves time at each penetration and gives a consistent result.
  • Two kinds of protection: a physical sheet barrier plus a termite repellent sealed inside the plastic films. Termites are turned away from the penetration, not just blocked.
  • Part of a certified system: made from the same material as Kordon TB and TMB, so pipe penetrations match the rest of a Kordon installation. The system meets AS 3660.1:2014 and is covered by a CodeMark certificate and a Limited Kordon Product Warranty.

Target pests

  • Subterranean termites

Where to use

The label's directions for use are headed 'All States except Tasmania'. Check the current label before supplying for Tasmanian projects.

  • New building work
  • Extensions
  • Renovations
  • Any job that needs termite protection where a pipe passes through a concrete slab
  • Slabs poured and cured to AS 2870 or AS 3600, where the slab forms part of the termite management system

Application

Pest Management Professionals installing Kordon should know the current AS 3660.1 (Termite Management – New Building Work) and the Building Code of Australia. Follow the product label and the Kordon installation manual.

  • Timing: install on top of the bedding sand once footings and plumbing are finished, before the steel reinforcing goes in and the slab is poured.
  • Fitting: push the collar down the pipe until the baseplate sits on the Kordon sheet or moisture membrane.
  • Securing: fasten two zip ties around the collar, one just above the baseplate and one about 50 mm higher.
  • Sealing: tape the baseplate to the sheet or membrane with duct tape at least 30 mm wide.
  • Equipment: zip ties and duct tape at least 30 mm wide.

Safety

The deltamethrin is sealed between the plastic films, but the product can irritate eyes and skin.

  • Wear gloves if you are likely to handle cut edges for long periods.
  • Wear clothing that prevents skin contact.
  • Respiratory protection is not required.
  • Read the Safety Data Sheet before use.

FAQ

  • Does the collar protect the building by itself? No. It protects only the pipe penetration. It must be part of a complete termite management system under AS 3660.1, which includes a slab built to AS 2870 or AS 3600, protection at the perimeter and construction joints, an inspection zone, and regular inspections by a qualified Timber Pest Inspector.
  • What if the pipe is a different size or there is a cluster of conduits? This collar has an internal diameter of at least 60 mm. For other sizes and odd-shaped or grouped penetrations, the Kordon system uses a hand-made collar and patch cut from Kordon sheet. A larger pre-formed collar (115 mm internal diameter) has also been listed on the label.
  • Can it be fitted to an existing slab, or used with a separate moisture membrane? It must go in before the concrete is poured, so it cannot be retrofitted to an existing slab. On in-fill slabs, the Kordon sheet and collar are laid on top of the moisture barrier and joined to it with duct tape.

Pack Size

Box of 100 pre-formed collars.

  • Collar internal diameter: 60 mm (minimum)
  • Collar height: 60 mm (minimum)
  • Skirt width: 40 mm (minimum)
  • Total baseplate width: 140 mm (minimum)
  • How to order: Garrards product code 823:KORD/50