Think Before You Spray: Avoiding Surface Damage from Treatments

Spray damage to surfaces is one of the most unwelcome phone calls a pest manager can receive. Termite and general pest work demands a working knowledge of building construction, from the outside loo of an older home that may give termites an entry point, to the slab type that dictates how a modern home is treated. Just as important is an understanding of wall, floor and timber finishes before any liquid treatment is applied, especially indoors.

Why surface damage matters

Some damage is obvious immediately, such as drilling through a water pipe or breaking a tile. The damage that hurts most is the surprise call days later from a customer saying your treatment has marked their floor, wall or furnishings. Most pest managers know to take care indoors, but it is easy to forget that even clean water can leave marks if it runs down a wall or drips onto a ceiling. The lessons below come from real Australian jobs investigated over many years.

Case 1: The rolled-up Persian rug

A customer with six or seven valuable Persian rugs wanted them protected from insect damage. The treatment was quoted as a light mist of a wettable powder product (this was before suspension concentrates were common). A few days later the customer phoned to say the colours had run in one rug. The technician had treated the rug and then rolled it up while still moist because there was not enough floor space for it to dry flat. The chemical was not the cause; the treatment process was.

Close-up of a treated floor surface showing how liquid can mark waxed or finished flooring
Waxed and coated floors can react to water alone, not just to the product in it.

Case 2: White dots on the kitchen lino

A pest manager using a new product for the first time was distraught to find white dots across the kitchen lino he had just treated. The householder was not concerned at all. For years she had waxed the floor weekly, and whenever a drop of water touched the waxy surface the lino turned white, then cleared as it dried. Knowing the floor’s history would have saved a great deal of worry.

Case 3: Streaks on rendered walls

Emulsifiable concentrate (EC) products contain solvents and emulsifiers that are then diluted with water. Those components can react with the surface of some paints. A streaking complaint on a rendered house near the ocean showed streaks the same colour as the residue on the paint tin, as though the treatment had cleaned the render rather than stained it.

How different formulations behave on surfaces

Formulation What to watch for Practical note
Emulsifiable concentrate (EC) Solvents and emulsifiers can soften or streak some paints and coatings Test an inconspicuous patch on painted and rendered surfaces first
Wettable powder (WP) Can leave a visible white residue on dark surfaces Residue usually cleans up with warm soapy water
Suspension concentrate (SC) Can also leave visible residue on dark surfaces Apply at the correct rate; avoid over-wetting
Water itself Runs, drips and pooling mark many finishes on their own Control droplet size, pressure and run-off; allow surfaces to dry flat

Water on its own is often the culprit. Garrards Pest Review (March 2000) reported discolouration where a cockroach treatment bleached a lime-based mottle-effect paint when water reacted with the finish. Freshly painted surfaces are also particularly likely to show spray marks.

Treating historic and heritage homes

Older Australian homes call for extra care. Shellac replaced oil and wax finishes in the 1800s and remained the dominant timber finish until lacquer took over in the 1920s. Shellac is a natural resin and is not waterproof; the timber is often oiled over the top for protection. Applying water to shellac-finished timber can leave white marks as the water reacts with the water-sensitive finish or the protecting oil. Where marking has occurred, an application of oil may remove the marks. If in doubt, treat the surface as heritage and keep liquid off it.

Pre-treatment checklist

  1. Ask about the surface. Has the floor been waxed or polished? Is the paint fresh? Is the timber shellac, oil or lacquer finished?
  2. Check the label. Use only APVMA-registered products at label rates and on the surfaces the label permits.
  3. Test a patch. Treat a small, hidden area first on any unfamiliar or valuable surface and check it once dry.
  4. Control the application. Use the right nozzle and pressure, avoid run-off and drips, and keep spray off ceilings and vertical surfaces unless the job requires it.
  5. Allow proper drying. Do not roll, stack or cover treated items while moist.
  6. Record and communicate. Note the surfaces treated and any advice given to the customer on your service report.

Wherever you apply a liquid treatment, take a few moments to consider whether the application could cause damage. That pause is far cheaper than a claim.

Available from Garrards

Garrards stocks a full range of professional formulations, application equipment and nozzles to help you match the treatment to the surface. Talk to your branch about the best option for sensitive indoor jobs.

Contact your local Garrards branch

Frequently asked questions

Can plain water damage surfaces during a pest treatment?

Yes. Water alone can mark waxed floors, lime-based and freshly applied paints, and shellac-finished timber. Controlling drips, run-off and drying is as important as product choice.

Which formulation type is most likely to affect paint?

Emulsifiable concentrates contain solvents and emulsifiers that can react with some paint surfaces. Wettable powders and suspension concentrates are more likely to leave a visible residue on dark surfaces, which usually cleans off with warm soapy water.

How do I treat timber with a shellac finish?

Shellac is not waterproof and can turn white when wet. Test a hidden patch, keep liquid to a minimum, and if marks appear an application of oil may remove them. Where possible, choose a treatment method that keeps liquid off the finish altogether.