Recording the Rate of Application: g/L, Not Percentages

Accurate pesticide application rate records are critical for your paperwork, for the information you give customers and for the durable notices that must be left after termite work. Labels tell you how much product to mix, so many mL per litre, but the question for the record is how to express what was actually applied so nobody can misread it. The answer is grams of active constituent per litre.

Why the way you write the rate matters

Over the years manufacturers, regulators and trainers have moved away from percentages toward weight or volume per weight or volume. Long-serving pest managers will remember Baygon 20 becoming Baygon 200 in about 1986, a change of expression from 20% to the equivalent 200 g/L. Cislin Residual Insecticide is commonly called Cislin 10 because it contains 10 g/L deltamethrin.

Percentage means parts per hundred; g/L or mL/L means parts per thousand. So 1% is the same as 10 g/L. The only difference is where the decimal point sits, and that is exactly where mistakes happen. Product concentrations are already expressed as g/kg or g/L on the label, so converting to a percentage just adds another chance for confusion.

The 1% problem

Saying ‘1%’ is open to two interpretations, especially with products containing 100 g/L. Take Biflex Ultra, which contains 100 g/L bifenthrin. If it is diluted at 1 L per 100 L, that is a 1% dilution of product. The concentration of Biflex in the emulsion is 1%, but the concentration of bifenthrin, the active constituent, is 0.1%. ‘Biflex 1%’ and ‘bifenthrin 1%’ are therefore ten times apart. That is why it is simpler and safer to write the product name, the label concentration in g/L and the active constituent, and then record the applied rate as g/L of active.

How to calculate the applied concentration

Expressed in g/L, the rate of application is easy to calculate and unlikely to be misinterpreted:

Concentration of emulsion (g/L) = label concentration (g/L or g/kg) x dilution

For Biflex at 100 g/L diluted 1 L in 100 L: 100 x 1/100 = 1 g/L bifenthrin.

Worked examples

Product Label concentration Dilution Applied concentration
Biflex 100 g/L bifenthrin 1 L / 100 L 1 g/L bifenthrin
Premise 200 g/L imidacloprid 250 mL / 100 L 0.5 g/L imidacloprid
Termidor 100 g/L fipronil 600 mL / 100 L 0.6 g/L fipronil
Cislin 10 g/L deltamethrin 150 mL / 5 L 0.3 g/L deltamethrin
Ficam 800 g/kg bendiocarb 30 g / 5 L 4.8 g/L bendiocarb

Note: in these calculations 1 g is taken to be equivalent to 1 mL (and 1 kg to 1 L). The dilutions shown are examples for illustrating the arithmetic; always use the rate on the current APVMA-approved label for the situation you are treating.

Step by step on site

  1. Read the label concentration of active constituent (g/L or g/kg) from the product container.
  2. Note the exact volume or weight of product added and the final volume of the mix.
  3. Divide product quantity by final volume, then multiply by the label concentration.
  4. Record the product name, active constituent, applied concentration in g/L, total volume applied and the area or situation treated.
  5. For termite work, transfer the same information to the durable notice fixed in the meter box or other location required in your state.

What the regulations expect

Queensland pest management regulations have required that the strength of active constituents be expressed as g/kg, g/L, mL/L and similar units rather than percentages, and this convention is now standard across Australian training and licensing. Every state and territory requires licensed pest managers to keep treatment records, typically including the product, active constituent, rate, quantity, date, location and the technician’s details, and to retain them for a set period. Australian Standard AS 3660 also calls for a durable notice after termite treatments identifying the chemical used and its rate. Check the record-keeping requirements of your own state or territory regulator and keep records for at least the prescribed retention period.

Biflex is a registered trademark of FMC Corporation. Premise, Cislin and Ficam are registered trademarks of Envu. Termidor is a registered trademark of BASF.

Available from Garrards

Garrards branches supply the products used in these examples along with treatment record books, termite notice labels and measuring equipment for accurate mixing. Ask your branch about training and compliance resources.

Contact your local Garrards branch

Frequently asked questions

Is 1% the same as 10 g/L?

Yes. Percentage is parts per hundred and g/L is parts per thousand, so 1% equals 10 g/L. The confusion arises over whether the 1% refers to the product or to the active constituent.

Should I record the product dilution or the active constituent concentration?

Record both the product and dilution used, but express the applied rate as g/L of active constituent. That is the figure regulators, auditors and future inspectors need and it cannot be misread.

Does 1 mL really equal 1 g?

For the purposes of these field calculations the examples assume 1 g is equivalent to 1 mL. Actual product densities vary slightly, but the assumption is accepted practice for recording rates.