Kordon

KORDON 250MM

Active ingredient5 g/kg deltamethrin (equivalent to 2 g/m² deltamethrin).

Code KORD/250

Downloads

Product details

Formulation

A ready-to-use, deltamethrin-treated sheet barrier. Treated webbing is laminated between plastic layers to form a flexible sheet with a black lower membrane. There is nothing to mix and nothing to dilute.

  • Formulation type: treated sheet (chemical in a non-soil matrix), installed using sheet-barrier principles
  • Poison group: Group 3A insecticide (deltamethrin, a synthetic pyrethroid)

Overview

Kordon Termite Barrier 250 mm is a flexible, deltamethrin-treated laminate that is built into a structure during construction. It deters concealed entry by subterranean termites. It is registered by the APVMA (approval number 60759) and is installed in line with AS 3660.1 and the Building Code of Australia.

Subterranean termites usually get into buildings through hidden routes such as wall cavities, slab edges and pipe penetrations. Kordon works as a physical barrier and also repels termites, so they are forced to go around it. Termites that do this have to build mud tubes in the open, where a competent inspection can find them before they cause serious damage.

This 250 mm wide roll is a narrow strip for perimeter barrier work, such as slab-edge rebates and in-fill slabs, rather than full under-slab coverage.

Product Highlights

  • Physical barrier plus repellent: the deltamethrin in the sheet repels termites and kills them on contact, adding a chemical layer of protection to a standard sheet barrier.
  • Long-life protection: the label states it deters concealed termite entry for at least 20 years, so there is no retreatment cycle. Regular inspections are still needed.
  • Holds up on a building site: the UV-stabilised membrane showed no significant loss of deltamethrin after at least 3 months exposed on a concrete slab. It gives off no respirable dust or VOCs, so it meets the requirements for low-allergen housing construction.

Target pests

  • Subterranean termites

Where to use

Approved for use in all states except Tasmania.

  • New building work
  • Extensions and renovations
  • Retaining walls
  • Other construction situations that need termite protection or management
  • Perimeter barriers on all construction types, including in-fill slabs and slab-edge rebates
  • Service penetrations that have to be protected separately

Application

Installers must complete Kordon Accreditation and Training and be assessed as competent in the unit Install Physical Termite Barriers. Follow the label, the Kordon Installation Manual and AS 3660.1.

  • Before installing: inspect the site, deal with any active nests of economically important termite species within the label's set distance, and remove stumps, roots, timber off-cuts and building debris from the footprint.
  • Essential design criteria: lay the lower (black) membrane facing the expected direction of termite attack, folding the sheet back on itself if needed. Make sure the sheet is compressed between two building elements.
  • In-fill slabs (before the pour): fix the sheet horizontally to the external finished brickwork, fold it back and secure it vertically to the inside of the brickwork using clouts and a construction-grade adhesive or bonding agent.
  • Slab-edge rebates (after curing): secure the sheet to the top of the slab edge with clouts or concrete nails. Extend it over the cavity into the outer masonry so it finishes flush with the outside face.
  • Joins, corners and patches: overlap the sheets, then tape with duct tape and bond with a construction-grade adhesive. Follow the label for minimum overlap and tape width.
  • Keep the label's minimum ground clearance so bridging can be found at inspection.
  • Equipment: clouts or concrete nails, duct tape, construction-grade adhesive or bonding agent, and cable ties for penetrations.
  • Fix a durable notice to the building as required by the Building Code of Australia.

Safety

Signal heading: none. The product is not scheduled under the SUSMP (classified exempt). The label does not list any specific PPE.

  • Do not touch or rub your eyes, nose or mouth with your hands. Contact with facial skin may cause temporary facial numbness.
  • Wash hands after use.
  • First aid: contact a doctor or the Poisons Information Centre on 13 11 26.
  • Deltamethrin is dangerous to fish. Do not contaminate ponds, waterways or drains.
  • Store in the original packaging in a cool, well-ventilated area. Do not store in direct sunlight for long periods.
  • Do not burn packaging or unused product. Either place off-cuts on the moisture barrier before the concrete pour, or bag them and take them to an approved waste facility.
  • See the Safety Data Sheet for more information.

FAQ

Q: Can a 250 mm perimeter strip be the only termite barrier? A: No. The label describes a perimeter barrier as a partial barrier. To comply with building regulations it must be combined with other approved termite barrier systems under AS 3660.1. Where the slab forms part of the barrier, it must be poured and cured to AS 2870.

Q: Does it need retreating, and are inspections still needed? A: It does not need retreating. The label states it deters concealed entry for at least 20 years. It does not stop termites from bridging the barrier, though. Inspections at least once a year, in line with AS 3660 and AS 4349.1, are still needed so that mud tubes are found early.

Q: Who can install it, and is it approved Australia-wide? A: Only Pest Management Professionals who hold Kordon accreditation and the physical termite barrier installation competency should install it. The label approves use in all states except Tasmania.

Pack Size

  • Kordon Termite Barrier roll, 250 mm wide
  • How to order: Garrards product code KORD/250