Piusi K400 Inline Flow Meter for Pest Control Spray Guns

The Piusi K400 is an inline oval gear flow meter for spray guns that gives professional pest managers a precise, battery-powered readout of the volume of chemical they have applied. It fits directly between the hose and the spray gun, can be calibrated to match your own spray equipment, and shows both a batch total for the current job and a running lifetime total.

What the K400 is

The K400 is an electronic oval gear meter designed for delivery control and measurement of low, medium and high viscosity fluids. Two oval gears inside the housing rotate as liquid passes through; an electronic card with a microprocessor counts the rotations, drives the display and handles calibration. The oval gear principle delivers high precision with very low pressure loss in a compact, lightweight body that is easy to install.

Because the meter has its own independent battery supply, it can be fitted either to a fixed transfer or distribution line or, as most pest managers use it, as a mobile accessory on a delivery valve or spray gun.

Key features and benefits

  • Fits directly to the spray gun, so the reading reflects what actually left the nozzle.
  • Field calibration to suit your pump, hose and gun combination.
  • Resettable batch readout for each job plus a non-resettable running total.
  • Independent battery power: no wiring to the vehicle or pump.
  • Compact (70 mm x 80 mm x 55 mm) and light (400 g), so it does not tire the operator’s wrist.
  • Low pressure loss, so spray pattern and pump performance are not noticeably affected.
Piusi K400 flow meter viewed from above showing the digital display and inlet and outlet ports
The K400 display shows a resettable batch total and a running lifetime total.

Performance

  • Precision: plus or minus 0.5 per cent across the flow rate range after calibration.
  • Repeatability: 0.2 per cent.
  • Pressure loss: less than 0.5 bar (7 psi) at maximum flow rate.

Specifications

Item Detail
Flow rate range 1 to 30 L/min
Batch readout (maximum) 99,999 litres
Total readout (maximum) 999,999 litres (plus x10 and x100 indicators)
Inlet 1/2 inch BSP female
Outlet 1/2 inch BSP female
Dimensions 70 mm L x 80 mm W x 55 mm H
Weight 400 g
Garrards part number SIL/F0047500A

Where Australian pest managers use it

Any treatment where the label specifies a volume per square metre or per linear metre is a candidate for an inline flow meter. The most common uses are:

  • Termite soil treatments. Pre-construction and post-construction chemical barriers are applied at set volumes per linear metre of trench or per square metre of slab area. A meter at the gun lets the technician confirm the volume in each trench section and record it on the job sheet and treatment certificate.
  • Perimeter and general pest treatments where the label states a spray volume for a given area.
  • Bulk tank and drum transfers, using the meter on a fixed line to measure product moved.

Accurate volume records support your compliance with the product label, demonstrate to the client that the specified rate was applied, and reduce chemical waste from over-application.

Calibration and care

Calibrate the meter against a known volume (for example, spraying into a measuring container) with the pump, hose and gun you normally use, and re-check periodically or whenever you change nozzles or pressure settings. Flush the meter with clean water after use, keep the gears free of grit by using a strainer upstream, and replace the battery when the display fades.

Safety and compliance

A flow meter is a measuring aid, not a substitute for reading the label. All pesticides must be APVMA-registered and applied strictly according to the label, and operators must hold the pest management technician licence required in their state or territory. Wear the personal protective equipment specified on the label and safety data sheet when handling the meter after use, as it will carry chemical residue.

Available from Garrards

The Piusi K400 flow meter (part number SIL/F0047500A) is available through Garrards branches, along with hoses, fittings, spray guns and pumps to suit. Ask the branch team about calibration and installation on your existing equipment.

Contact your local Garrards branch

Frequently asked questions

Can the Piusi K400 be calibrated to my spray rig?

Yes. The K400 has an onboard microprocessor with a calibration routine, so it can be matched to your particular pump, hose and gun combination. Re-check calibration whenever you change nozzles or pressure.

Will the K400 reduce my spray pressure?

Pressure loss through the meter is under 0.5 bar (7 psi) at the maximum 30 L/min flow rate, so most pest control rigs will see no practical change in spray pattern.

What fittings does the K400 use?

Both the inlet and the outlet are 1/2 inch BSP female threads, which suit common Australian spray hose fittings.