Kordon

KORDON 150MM X 50M PACK OF 2

Active ingredientDeltamethrin 5 g/kg (equivalent to 2 g/m² deltamethrin)

Code KORD/150

Downloads

Product details

Formulation

  • Formulation type: pre-fabricated, flexible sheet barrier with deltamethrin in the sheet. The label calls it a chemical in a non-soil matrix, and AS 3660.1-2014 classes it as a sheet material.
  • Chemical family: synthetic pyrethroid (deltamethrin)
  • Supplied as a narrow roll for perimeter installations: 150 mm wide × 50 m long

Overview

Kordon Termite Barrier is a flexible sheet that contains deltamethrin. It is built into a structure during construction to deter subterranean termites from getting in unseen. This 150 mm × 50 m roll is a narrow width for perimeter work, such as slab edge rebates, in-fill slabs and wall cavities. These are the high-risk areas where termites commonly find a hidden way in.

Deltamethrin strongly repels termites, so they avoid close contact with the sheet. Termites that try to get around it have to build mud tubes, which a qualified inspector can find at a routine inspection. The colony can then be dealt with before serious damage is done.

A perimeter installation is a partial barrier. To comply with AS 3660.1 and the Building Code of Australia, it must be used with the slab, poured and cured to AS 2870, and with other approved termite management systems. Service penetrations must be protected separately. Kordon is approved by the APVMA under approval number 60759/52075.

Product Highlights

  • Repels as well as blocks: termites are not just stopped by a physical layer. The deltamethrin pushes them away from the barrier, and any attempt to get around it leaves mud tubes that show up at inspection.
  • Rated for a long working life: based on the available data and ongoing field trials, the barrier deters concealed termite entry for at least 20 years. The membrane is UV-stabilised, and testing showed no significant breakdown of deltamethrin after at least 3 months exposed on a concrete slab. This matters because perimeter strips often stay exposed until the build is finished.
  • Suits many building details: the sheet can be cut, folded back on itself and joined to fit rebates, cavities and in-fill slab details. It gives off no respirable dust or volatile organic compounds, so it meets the requirements for building products used in low-allergen housing.

Target pests

  • Subterranean termites

Where to use

Approved for use in all states except Tasmania.

  • New building work
  • Extensions and renovations
  • Retaining walls
  • Other construction situations that need termite protection or management
  • Perimeter barriers in all construction types, including in-fill slabs and slab edge rebates

Application

Only accredited installers should install this product. Pest Management Professionals need to have completed Kordon Accreditation and Training and be assessed as competent in the Install Physical Termite Barriers unit. Follow the label, the Kordon Installation Manual, AS 3660.1 and the Building Code of Australia.

  • Before installation: inspect the site and eliminate any active nests of economically important subterranean termites within the property boundary, up to 50 m from the new work. Remove stumps, roots, timber off-cuts and building debris from the work area.
  • Two design rules apply to every installation. The black (lower) membrane must face the direction of expected termite attack, and the sheet must be compressed between two building elements.
  • Slab edge rebates: once the slab has cured, fix the sheet to the top of the slab edge with clouts or concrete nails. Run it across the cavity into the outer masonry wall, finishing flush with the outside face.
  • In-fill slabs: if installing before the pour, fix the sheet horizontally to the external brickwork, fold it back and fix it vertically to the inside of the brickwork using clouts and a construction-grade adhesive. Otherwise, use the slab edge rebate method.
  • Joins and patches: overlap the sheets and seal with duct tape at least 30 mm wide, plus a construction-grade adhesive or bonding agent. See the label for the minimum overlap.
  • Leave enough ground clearance to inspect for bridging, as set out on the label.
  • Protect service penetrations separately, using Kordon collars or the label's manual patch-and-collar method secured with duct tape and cable ties.
  • Fix a durable notice to the building as required by the Building Code of Australia.
  • Recommend inspections at least once a year, in line with AS 3660 and AS 4349.1.

Safety

  • Signal heading: none on the label
  • Poisons schedule: none allocated (exempt from poison scheduling)
  • PPE: no special protective clothing or equipment required. The product can irritate eyes and skin.
  • Do not touch or rub your eyes, nose or mouth with your hands. Contact with facial skin may cause temporary numbness. Wash hands after use.
  • Deltamethrin is dangerous to fish. Do not contaminate ponds, waterways or drains.
  • Store in the original packaging in a cool, well-ventilated area, out of direct sunlight for long periods. Do not burn packaging or off-cuts.
  • First aid: contact a doctor or the Poisons Information Centre on 13 11 26.

FAQ

  • Can the 150 mm perimeter strip be used as the only termite protection on a job? No. A perimeter barrier is only a partial barrier. It must be used with a slab poured and cured to AS 2870 and with other approved termite management systems under AS 3660.1. Service penetrations need their own protection, such as Kordon collars.
  • Who can install it, and where? Only Pest Management Professionals who have completed Kordon Accreditation and Training and are competent in installing physical termite barriers. The directions for use cover all states except Tasmania.
  • If Kordon is installed, are inspections still needed? Yes. Kordon deters concealed entry but does not stop termites from bridging the barrier. Termites that try to get around it build mud tubes, so inspect at least once a year (or as AS 3660 and AS 4349.1 require), keep the required ground clearance and make sure trades do not damage exposed sheet during construction.

Pack Size

Garrards product code: KORD/150

  • Pack of 2 rolls
  • Each roll: 150 mm wide × 50 m long (7.5 m²)
  • Total per pack: 100 m of barrier (15 m²)
  • How to order: order online using product code KORD/150, or contact Garrards with this code.